Bloom Surge Fragrance Oil for Candles & Diffusers

Bloom Surge is a floral oriental that opens green. Tea leaf and bergamot come first, then osmanthus with its apricot-like sweetness, followed by orchid, jasmine, rose, freesia and orange blossom. Patchouli, musk and vanilla sit underneath. It smells like a garden at dusk: floral and full, but with a warm resinous floor rather than a sugary finish.

Most floral fragrance oils either turn sugary and thin or go heavy and soap-like. Bloom Surge is built the second way on purpose: the flowers sit above a resinous base instead of floating on top of it. That base is why the scent keeps its shape in hot wax and still reads as flowers in the third hour of a burn, rather than collapsing into powder.

Most makers start between 6% and 10% by weight of wax. For one pound (16 oz) of wax that works out to roughly 0.96 to 1.6 oz of fragrance oil. Check your wax supplier's maximum load first, because base paraffin, container soy and coconut blends all hold different amounts. Bloom Surge behaves well at 8%, which is a sensible first test.

Four causes cover almost every weak candle: too little fragrance, the oil added at the wrong temperature, a wick too small to melt to the edge of the jar, or a cure that was cut short. Add Bloom Surge at 180 to 185°F, stir for two full minutes, size the wick to the vessel, and cure before judging. Adding more oil than the wax can hold does not help; it seeps out instead.

Give soy one to two weeks, coconut blends seven to ten days, and paraffin about 48 hours. Fragrance needs that time to bind with the wax, and a candle tested too early reads weaker than it will later. This matters more with a base-heavy scent like Bloom Surge, where the patchouli and musk are the part that develops last.

Yes. Start at 2% to 5% of your oils and add it after trace at the coolest temperature your recipe tolerates. Dense florals can speed trace, so treat this one as a fast mover until your own formula proves otherwise: line the mold first, and stir by hand rather than stick-blending once the oil goes in.

It is a fragrance oil, not an essential oil. It is built from aroma materials to hold one specific accord consistently from batch to batch, rather than distilled or pressed from a single plant. That is also why it can carry notes no single botanical contains, such as the tea leaf and bergamot opening over osmanthus.

In a reed diffuser, dilute it into a diffuser base to the strength you want. Fragrance oil is not water soluble, so an ultrasonic or mist diffuser needs a solubilizer or an alcohol-based carrier, otherwise the oil floats and can clog the unit. Never put neat fragrance oil into a water tank.

Treat it as you would any concentrated fragrance: keep the bottle out of reach, never let a pet lick a spill, and ventilate the room while you work. Cats and dogs are more sensitive to concentrated fragrance than people are. A finished, properly diluted candle or spray is a different exposure from an open bottle, and a spill is the bigger risk.

Flash point is the temperature at which the oil gives off enough vapor to ignite briefly if a flame is present. Bloom Surge is 207°F (97°C) closed cup, which is high for a fragrance oil and leaves comfortable working room in melted wax. It is not a measure of scent strength, and a high flash point does not make the oil non-flammable.

Yes, diluted: 0.5% to 2% in lotions and other leave-on products, and 1% to 10% in perfume or fine fragrance. Those are starting ranges. The ceiling for each application is set by the IFRA certificate, so check it before locking a formula, and patch test anything that stays on skin.

Ask us and we will send both before you order: the IFRA certificate covering the categories this scent is cleared for, and the safety data sheet for the batch. If you need them for a formulation review or for retail compliance, tell us the application and we will point you to the right category.